Computherm Wireless Thermo Control System User Manual

Computherm Wireless Thermo Control System User Manual

Computherm Wireless Thermo Control System User Manual Rating: 3,5/5 1975 reviews
Control

Wireless Digital Plug in Heating Thermostat Remote Control Electric RF Socket. Wireless Room Heating Thermostat for Under Floor Water Heating System. Of the receiver and to observe the instructions of the manufacturer of the devices. View and Download Computherm Q7 RF operating instructions manual online. Programmable, wireless (radio-frequency) digital room thermostat. Related Manuals for Computherm Q7 RF. COMPUTHERM Q7 RF Programmable, wireless (radio-frequency) digital room thermostat Operating Instructions. Page 2: Product Overview.

Building and engineering contracts by b s patil pdf 2017. Building And Engineering Contracts By B S Patil Pdf To Word. Vacancies for B.Pharm, M.Pharm, B.Sc, M.Sc, Ph.D candidates. ( PDF) Oblivious Neural Network. Amazon.in - Buy Building and Engineering Contracts book online at best prices in india on Amazon.in. Read Building and Engineering Contracts book reviews & author details and more at Amazon.in. Free delivery. Building and Engineering Contracts Hardcover – 2011. By B.S.Patil (Author). Be the first to review this item. Contents: Foreword. About the Author: B S Patil is a contracts and arbitration consultant based at Pune. He has had a distinguished academic and professional career. He has gained wide experience in the planning and supervision of construction projects and in the preparation of legal documents related to engineering projects. The Urdu word `Sulah' in the deed has a different connotation from the words `Supard Salsi. Building & Engineering Contracts - B S Patil. Patil B.S., Civil Engineering. Estimating And Costing In Civil Engineering Pdf Civil Engineering Estimating And Costing Pdf Estimating And Costing In Civil.

• Edited by Foxit PDF Editor COMPUTHERM Q3 Copyright (c) by Foxit Software Comp For Evaluation Only. Digital room thermostat software!

Operating Instructions. • GENERAL DESCRIPTION OF THE THERMOSTAT COMPUTHERM Q3 type switched-mode room thermostat is suitable to regulate the overwhelming majority of boilers and air conditioners available in Hungary. It can easily be connected to any gas boiler or air conditioning device that has a double wire connector for a room thermostat, regardless of whether it has a 24V or 230V control circuit. • The switching sensitivity of the thermostat can be set to ±0.1°C or ±0.2°C (default setting). This means the difference between the ad- justed temperature and the actual tem- The information shown on the liquid crystal display of the thermostat perature measured includes the following: during the switch- process. • es the boiler on at 19.8°C or below, and switches it off at 20.2°C or above.

Please refer to Section 4.1 for the modification of the factory default switching sensitivity of ±0.2°C. LOCATION OF THE DEVICE It is reasonable to locate it in a room used regularly or for many hours per day so that it is in the direction of natural ventilation in the room but protected from drought or extreme heat (e.g. • the radiator valve with a manual control knob in the room where the room thermostat is to be located, otherwise the thermostatic head may disturb the temperature control of the flat. INSTALLATION OF THE THERMOSTAT • To install the thermostat, detach the rear panel of the thermostat from the front panel by loosening the screws at the bottom of the cover as shown in the. • • Using a small screwdriver, remove the cover of the terminal block from the inner side of the rear panel. The thermostat controls the boiler or air conditioner through a potential-free alternating relay that has the following connection points: No.

2 (COM) and No. • To prevent electric shock, replace the inner cover removed for the connection of wires after the assembling process has been completed. Always consider the loadability of the thermostat and follow the manufacturer’s instructions of the heating or cooling equipment.

The device must be installed and connected by a qualified professional. • with the diagram in the battery compartment. After the batteries have been inserted, the display flashes the measured room temperature. (If this information fails to appear on the display, press the “RESET” button with a wooden or plastic stick. To press the button, do not use any electrically conductive materials, e.g. • 4.1 Selecting the Switching Sensitivity (Accuracy) The switching sensitivity of the thermostat can be selected or adjusted by the uppermost jumper. With factory default settings the jumper is located on the central and right pins, resulting in a switching sensitivity of ±0.2°C.

Related News

Computherm Wireless Thermo Control System User Manual
© 2019